Knowledge Base

Pro Tools | Ultimate™ or Pro Tools | HD™ on a separate computer via Avid® Satellite Link

Introduction

This DAW Sync option provides the tightest & fastest sync with Pro Tools® on a separate computer - using Avid® Satellite Link, but without the direct control of Pro Tools® for recording & cueing using DAW Control. Any version of Pro Tools | Ultimate™ or Pro Tools | HD™ 11 or higher are required to serve as a Satellite Admin. This setup is as comparably fast & easy as setting up on the same machine. There are only some minor differences.

DAW Control is not possible with Pro Tools® on a separate computer, as it relies on Apple's Accessibility API on the same computer to communicate with Pro Tools® for advanced recording controls, like track naming, muting, record enabling etc. The Accessibility API requires the app to be controlled (Pro Tools®) and the controlling app (ADR Master) to be on the same computer.

Setting up Satellite Link is quite simple and straight-forward & should only need to be done once to have ADR Master connected to the Satellite Link network. Many of these settings should already be correctly setup by default - it’s just a case of manually confirming they are correct.

ADR Master Sync Preferences

Click on Satellite Link in the Sync Method field.

In the Pro Tools | Satellite Link settings box at the bottom of the window, set the Control Mode to Pro Tools on separate computer.

If not already, set the Port field to 28282.

Port 28282 is the default port used by Pro Tools. Feel free use another port if 28282 is not usable in your network or if you want to create different Satellite “subnets”, e.g. one for each studio.

To give this computer’s ADR Master a unique Satellite name that would show up in Pro Tools®’ Satellite options, type it in the Satellite Name field. This is especially useful for identifying each instance of ADR Master, if running multiple ADR Master Satellites on the same network.

The Network Interface address selection allows for selecting the network interface to use. Make sure to select the interface corresponding configured with the IP address also used in the Pro Tools® on the other computer you want to connect to.

The steps up until this point in ADR Master should only need to be done once. After that - ADR Master should always be automatically connected to the Satellite network when it is available - unless the Satellite settings are changed.

Next go to the timeline tab on the top left & make a note of the timecode rate of the current timeline being used, so that can be matched in Pro Tools®.

Timeline frame rate of a timeline in ADR Master

Mis-matched Pro Tools® Session Timecode Rate & ADR Master TC Frame Rate will cause out-of-sync playback. This needs to be checked which each different session.

Enable the Sync State button to the left of the transport controls in the middle of the main ADR Master window.

Sync online button in ADR Master

In Pro Tools®, go to the Session Setup window and confirm that the timecode rate & range match those set in ADR Master.

Then go to the Setup menu > Peripherals > Satellites tab:

Satellites Preferences in Pro Tools

Make sure that Administrator is selected under the Mode box.

In the Administrator box, make sure Administrator is selected as System 1.

Under the Advanced Network Settings, check that the Interface tab is set to the same network that was chosen in ADR Master. Check that the TCP/UDP Port: value to the same value also selected in ADR Master (28282 by default).

In the Administrator box, select the ADR Master instance with the name you have selected in the dropdown menu for the next available System (2 by default if no other Satellites connected).

If for any reason ADR Master does not show up in the list, re-check all the settings & hit the Reset Network button.

Click OK.

ADR Master is now connected to the Satellite network, but will not yet start syncing until it is online in the Pro Tools® Transport window.

First, check that the expanded Satellite Synchronisation box is showing in the Transport window by clicking on the downwards pointing arrow on the top right of the window, & making sure the Synchronization controls are enabled.

Finally, enable the Satellite Devices that now appear in the Transport Bar in Pro Tools®, including the arrow keys adjacent (which provide positional information). There should be one for Pro Tools® and one for ADR Master.

Pro Tools Transport Window

This will also automatically enable the Sync button to the left of ADR Master’s Transport controls.

ADR Master Satellite Link is now online & ready to go. Hit play in Pro Tools® and make sure ADR Master follows.