With Video Slave and ADR Master, you can leverage the accuracy of genlocked playback to get the tightest synchronized playback possible. If you are not familiar with the terms "genlock" or "video reference", this article will try to shed some light on the topic and hopefully help clearing things up.
What is genlock, anyway?
When working in a professional post production environment, the terms "video reference" and "genlock" will pop up after some time. But what does genlocking mean and what's a video reference, exactly?
Generator locking or "genlocking" in short is a technique from the video world used to synchronize two or more video signals to coincide with a central timing reference signal - the "video reference". The video reference essentially is a standard video signal which does not contain any picture information but only sync pulses. A sync pulse (shown in the image above) in turn marks the "frame edge" - the point in time where the old video frame ends and the new frame begins. A video reference signal thus only contains frame edge information. The number of sync pulses per second depends on the video reference frame rate - a 25 fps video reference signal will contain 25 sync pulses per second for example.
When a video reference signal is connected to the appropriate reference input of a video card for example, the video card will try to "lock" to that sync pulse so that the card's frame edge coincides with the sync pulse's frame edge. This process is then called "generator locking" as the device locks its own video frame generator to the external reference signal. Once locked, the video card will refresh its output in time with the sync pulses of the reference signal.
In the video world, there's no way around genlocking when two or more video sources are to be mixed together. The frame edges must be aligned to avoid flickering or tearing.
Video reference in an audio postproduction environment
You might ask yourself now why this clearly video related technology is used in the audio postproduction environment. Genlocking is used in both small studios but also in larger facilities. In larger facilities, video reference signals are used as what's called "house sync" or "house reference". As stated above, video reference signals are standard video signals. As such, they can be distributed easily over longer distances throughout a large facility. Aside from the frame edge and thus timing information, video reference signals can also be used as speed reference for other devices. Sync generators like the Rosendahl Nanosyncs HD for example can generate wordclock (the audio counterpart to video reference) in accordance to the video reference input. In general, video reference can be considered a very stable and reliable timing source whereas device internal clocks might drift over time. One device's clock might be slightly faster, the other device's clock slightly slower. Over time, a sync drift may occur. Video reference will prevent that.
Why genlock in Video Slave and ADR Master?
But genlocking also makes sense in smaller studios and even if you're only using one computer and Video Slave/ADR Master. Let's start by explaining what happens when playing back movies in sync with an external video device attached to Video Slave/ADR Master without genlock.
When starting playback in Video Slave or ADR Master, it will start the so called "output loop" of the attached Blackmagic or AJA device. From then on, the external video device will pull video frames at a steady rate - the output frame rate, so e.g. 25 fps - from its host application. When you hit play in your DAW, Video Slave/ADR Master will start playback as soon as it receives the first timecode address and send video frames to the external video device for display. There's however no mechanism in place to make sure that this happens on the frame edge of the external video device. This will result in an offset of up to one frame. The following image illustrates the problem:
The top line shows the video frames rendered on the video device, the red lines represent the timecode addresses Video Slave/ADR Master receives from Pro Tools. Video Slave/ADR Master receives the first timecode from Pro Tools shortly after the frame edge of the external device. It will start playback immediately after the timecode is processed. But although it writes the new video frame to the device immediately, it will not be visible before the next frame edge yielding an offset of up to one video frame.
This doesn't mean that playback will always be off by almost one frame however. The case above shows the worst case scenario. Statistically speaking, the delay will be at around 1/2 movie frame or speaking in milliseconds: around 20 milliseconds (for standard frame rates smaller than 30 fps)
Genlock to the rescue!
The only way to get rid of this sync offset is to genlock both Video Slave/ADR Master and also the DAW. Attaching a video reference to the video player alone doesn't solve the problem as the DAW will still send its timecode at some point in between the frame edges. Only if the DAW is also locked to video reference, it will send its timecode synchronized to the frame edge of the reference signal. To be able to lock Pro Tools to video reference, an Avid SYNC I/O or SYNC HD is required. The SYNC HD user manual states: "When video reference is present, Pro Tools automatically aligns to frame edge."
This then yields a playback behavior like this:
Video Reference in Video Slave and ADR Master
To benefit from genlocked playback with Video Slave and ADR Master, a Blackmagic or AJA video card with video reference input is required. When starting up, Video Slave/ADR Master will scan the system for all available cards and enable the genlock automatically. Video Slave/ADR Master will always use the genlock of the first card available in the system as timing and speed reference.
If a valid reference is attached, Video Slave/ADR Master will display "Locked" with Blackmagic devices and the frame rate of the attached video reference with AJA devices in the application's controller bar next to the main timecode counters
In both cases it is essential that the video reference frame rate matches the output frame rate of the Blackmagic or AJA device! Make sure to select the correct output frame rate for the corresponding device in Video Slave/ADR Master's Display preferences. If the output frame rate doesn't match, the sync behavior is undefined. Other than that, there's nothing you need to do to make Video Slave/ADR Master use the video reference.